Fluke insulated square screwdriver

- Squared Screwdriver: 2 sizes available, sold individually
- Certified to 1000 V AC, 1500 V DC
- Ergonomic handle causes less strain, provides maximum torque

The screwdriver tips, made from hardened chromium-molybdenum-vanadium (CMV) steel blades to minimize wear, fit and grip the fastener properly to apply maximum torque without damage to the head. These screwdrivers are perfect to keep in your tool bag and bring on whatever jobsite you’re on. Always be safer and grab for an insulated screwdriver. Fluke offers two sizes of square head screwdrivers, sold individually or as kits:
- ISQS1 Insulated Squared Screwdriver #1, 4" shaft; (4 mm square tip, 100 mm shaft)
- ISQS2 Insulated Squared Screwdriver #2, 5" shaft; (6 mm square tip, 125 mm shaft)

NFPA 70E requirements
Both drivers have handles that are ergonomically designed for a strong grip without cramping your hand up whether you’re in gloves or not. Precision insulated tools that meet NPFA 70E requirements. Every screwdriver is individually tested to 10,000 volts and certified to :
- 1000 V AC
- 1500 V DC
The tool is also backed by a limited lifetime warranty.

Fluke Insulated Hand Tool Lifetime Limited Warranty

Each Fluke Insulated Hand Tool will be free from defects in material and workmanship for its lifetime. As used herein, “lifetime” is defined as seven years after Fluke discontinues manufacturing the product, but the warranty period shall be at least fifteen years from the date of purchase. This warranty does not cover damage from neglect, misuse, contamination, alteration, accident or abnormal conditions of operation or handling, damage or normal wear and tear of mechanical components. This warranty covers the original purchaser only and is not transferable.

Recommendations for use and in-service care of Fluke Insulated Hand Tools
The following is guidance concerning the maintenance, inspection, retest and use of Fluke Insulated Hand Tools.

Warning – to avoid electrical shock or personal injury:
- Keep fingers behind the finger guards of the tool. Never touch conductive parts.
- Always wear approved eye protection.
- Do not use in wet or damp locations. Do not use unless the tool is clean and dry.
- Do not apply excessive force or stress to the tool insulation that may cause damage. Examples include using the insulated surfaces as a fulcrum to pry or wedge or gripping insulated tool handles with other tools such as pliers or wrenches to increase torque or leverage.

If the tool is used in a manner not specified, the protection may be impaired.

Storage

Insulated hand tools should be properly stored to minimize the risk of damage to the insulation due to storage or transportation. These insulated hand tools should be stored separated from other tools to avoid mechanical damage or confusion with uninsulated tools. Furthermore, these insulated hand tools should be prevented from contact with excessively hot surfaces (for example steam pipes) or exposure to excessive UV- radiation.

Inspection before use

Before use, each Insulated Hand Tool should be visually inspected by the user. If there is any doubt concerning the safety of the insulated hand tool, it should be subjected to examination by a competent person and if necessary retested to determine suitability or disposed of to prevent further use.

Temperature

Insulated Hand Tools should be used only in environments having temperatures between –20 °C and +70 °C and, for tools marked “C”, between –40 °C and +70 °C.

Periodic examination and electrical retesting

An annual visual examination by a suitably trained person is recommended to determine the suitability of the Insulated Hand Tool for further service. If an electrical retest is required by national regulation or in the case of doubt after visual examination, the applicable dielectric test of IEC 60900 for insulated hand tools should be performed.

ISQS1
Insulated Squared Screwdriver #1, 4"; 4 mm, 100 mm

ISQS2
Insulated Squared Screwdriver #2, 5"; 6 mm, 125 mm

Download

Produk Lainnya

Kennedy Water Pump Pliers 250mm, 40mm Jaw Capacity

Linesman Pliers
Serrated jaws for gripping nuts, bolts, studs etc. with side cutter and slip guard
safety handles.

Spark-resistant tools are used to eliminate the chances of accidental fires or explosions in potentially combustible or explosive environments. They resist the sparks that a standard tool could potentially create when striking hard surfaces. The use of spark resistant tools is essential in many industrial applications such as petroleum and chemical manufacturing, spray booth operations, the marine industry, the mining industry, the paper industries, or any location where flammable vapours or combustible residues are present. Beryllium Copper are manufactured to 30-10HRC and offer a breaking strain of 1117 N/m - 1236 N/m. Spark-resistant tools must be maintained with special care. Frequent cleaning/re-dressing to remove ferrous particles or contaminants, which may impair the spark resistant properties, is essential.

Kennedy 3 to 30mm, Brass/Copper/Stainless Steel, Single Stroke Tube Cutter

With a high strength cast body and a single cutting wheel with two rollers, this pipe utter is suitable for stainless steel, brass and copper tubes. Fitted with a deburring blade, spare cutter wheels are available to purchase.

Features and Benefits
• Cast body is highly durable and robust
• Can be used with stainless steel, brass and copper tubing for versatility
• Spare cutter wheels can be purchased to keep the product working to an optimum
• Fitted with a highly efficient deburring blade for accurate and easy cutting

Typical Applications
• DIY
• Construction
• Plumbing

Kennedy Ball Pein Hammer, 1-1/2lb, Wood Shaft, Polished Face

This range of ball pein hammers have been manufactured from high-grade drop forged steel that has been fully heat-treated. Ideal for use with cold chisels, punches, rivets and for the shaping of metal. With fine grain, forged steel head, hardened and tempered with polished faces complete by a hardwood shaft. Available in varying sizes to suit your needs.

Features and Benefits
• Manufactured from drop forged high grade steel making for a robust product
• Head is heat treated for durability
• Solid wooden handle for bolstered grip and control when wielding

Typical Applications
• Ideal for use with cold chisels, punches, rivets and for the shaping of metals

Kennedy Retractable, Trimming Knife, Steel Blade

Suited for both left and right handed users, this retractable safety knife is ideal for regualr use. Supplied with five heavy duty carbon steel blades that can be stored in the body of the knife, the slimline, diecast body has a contoured grip which provides a greater degree of control and comfort. Finished with a handy lanyard hole at the base of the knife.

Features and Benefits
• Possesses extra storage in the body for up to five blades
• Slimline design allows you to cut in confined spaces
• Contoured, ergonomic design increases user comfort and grip
• Boasts a high quality carbon steel blade that holds a good cutting edge even with extensive use
• Retractable feature ensures safety and reduces the risk of accidental cutting

Typical Applications
• Construction
• Carpentry
• Electrical
• Plumbing
• Warehousing
• Retail
• Production Line

Warnings
• This product is only available to buy for over 18's

Fluke insulated square screwdriver

Informasi Pemesanan