Pump & Lubricants
Kennedy Hydraulic Nipple, 90°, 1/8" BSP(T), Steel
For use with Kennedy grease guns and all other hydraulic grease equipment.
Download
Produk Lainnya
• No close tolerances
• Pulsation-free flow
• Laminar flow
• Non-impinging, preventing degradation
• Does not emulsify or damage delicate and shear sensitive products
• Includes in-line, close-coupled, side-by-side, over-under, and self-priming configurations
• Pulsation-free flow
• Laminar flow
• Non-impinging, preventing degradation
• Does not emulsify or damage delicate and shear sensitive products
• Includes in-line, close-coupled, side-by-side, over-under, and self-priming configurations
NEOVAC is well-known as a synonym for high quality vacuum pump oil. We have received endorsements of NEOVAC as the oil used by many vacuum pump manufacturers due to the high level of trust placed in NEOVAC's performance. NEOVAC is used in vacuum equipment in applications such as semiconductors, silicon wafers, vacuum deposition, heat treatment, and packaging and contributes to productivity improvements.
NEOVAC MR Series
Rotary pump vacuum oil is used with the purposes of lubrication and the preservation of airtight seals. It has a low steam pressure, suitable viscosity, and is difficult to emulsify (it has anti-emulsification properties). In other words, it easily separates from water and removes water.
MR-100 : Standard for small pump
MR-200 : Standard for small pump
MR-250 : Standard for small pump
MR-200A : Improved heat and oxidation. Moisture suction is supported
MR-250A : Improved heat and oxidation. Moisture suction is supported. For large pump
NEOVAC SX & SY
Diffusion pump vacuum oil is sprayed either as molecules or as a steam and is used to obtain a vacuum state. It is necessary for these oils to be chemically stable such as by having low steam pressures, by not being transformed due to heat (heat resistance), and by not reacting easily with oxygen (oxidation resistance).
SX : For surface treatment equipment. (vapor deposition, sputter, heat treatment)
SY : For surface treatment equipment. (vapor deposition, sputter, heat treatment)
NEOVAC MR Series
Rotary pump vacuum oil is used with the purposes of lubrication and the preservation of airtight seals. It has a low steam pressure, suitable viscosity, and is difficult to emulsify (it has anti-emulsification properties). In other words, it easily separates from water and removes water.
MR-100 : Standard for small pump
MR-200 : Standard for small pump
MR-250 : Standard for small pump
MR-200A : Improved heat and oxidation. Moisture suction is supported
MR-250A : Improved heat and oxidation. Moisture suction is supported. For large pump
NEOVAC SX & SY
Diffusion pump vacuum oil is sprayed either as molecules or as a steam and is used to obtain a vacuum state. It is necessary for these oils to be chemically stable such as by having low steam pressures, by not being transformed due to heat (heat resistance), and by not reacting easily with oxygen (oxidation resistance).
SX : For surface treatment equipment. (vapor deposition, sputter, heat treatment)
SY : For surface treatment equipment. (vapor deposition, sputter, heat treatment)
Hot dip protective plastic coating moulds around the component or tool to provide 100% coverage and protect against impact and corrosion.
Features and Benefits
• Hot dip plastic coating moulds itself around the part to provide 100% coverage and protect against corrosion and impacts for up to ten years
• Easy part identity through the translucent coating
• Simple to remove by peeling off
• Once removed, leaves behind a thin oil film to provide short term protection against corrosion
• Removed coatings may be reused saving cost
Notes
• Each single block measures (L)-150mm (H)-50mm (W)-80mm
• Working temperature 130°C to 160°C (for optimum results 140°C to 145°C)
Warnings
• Never directly apply heat to melt the protective dip
• Always use with a suitable melting pot
Features and Benefits
• Hot dip plastic coating moulds itself around the part to provide 100% coverage and protect against corrosion and impacts for up to ten years
• Easy part identity through the translucent coating
• Simple to remove by peeling off
• Once removed, leaves behind a thin oil film to provide short term protection against corrosion
• Removed coatings may be reused saving cost
Notes
• Each single block measures (L)-150mm (H)-50mm (W)-80mm
• Working temperature 130°C to 160°C (for optimum results 140°C to 145°C)
Warnings
• Never directly apply heat to melt the protective dip
• Always use with a suitable melting pot
These imperial, straight type hydraulic grease nipples are suited for use with Kennedy® grease guns and all other hydraulic grease equipment. With an all steel construction, the product is resilient and available in three varying sizes.
Features and Benefits
• Available with three varying thread connectors to suit your existing tool
• Manufactured from durable steel to bolster product longevity
• Can be used with grease guns as well as all other hydraulic grease equipment for versatility of use
Typical Applications
• Engineering
• Automotive
Features and Benefits
• Available with three varying thread connectors to suit your existing tool
• Manufactured from durable steel to bolster product longevity
• Can be used with grease guns as well as all other hydraulic grease equipment for versatility of use
Typical Applications
• Engineering
• Automotive